how to hook up a 4 channel amp into stock radio stereo how to hook up a 4 channel amp into stock radio stereo

How to hook up amp to factory car stereo, add your answer

international dating site for serious relationship

I have read that the amp also powers the door speakers. Alternatively, if on a tight budget AND your amp has an input marked "high level" or "speaker level," it is safe to hook speaker wires from your factory deck to it.

Some have that option.

Amp Hook Up To Factory Radio. Portable Factory Finished Cabins – Enterprise Center Giddings

I did it all with a little hard work and wal mart. There is a method to the madness; if you unplug all your drives and your video card, you should be able trace all the wires back to 2 or 3 bunches unless you have a modular PSU, in which I'm not sure how this would workyou'll want to connect the amp to as many bunches as you can.

Fred hamdun February 16, at Could this really be the case. As for the speakers once again a schematic is the best way but you can take fir instance the left front speaker wires from the new stereo with the unit turned on and tuned to a station and through trial and error find the two that feed the left front speaker or Ive heard you can use a 9v battery and listen for a buzz to identify the correct wires, or use the continuity tester on the multimeter to identify the wires.

Frank June 22, at Perhaps a faulty line output converter?

lachido dating divas

Comment by ModifiedLife on March 2nd, Since they want to put together the cheapest stereo they can and charge a cores mais lembradas yahoo dating load of money for it, they use crappy speakers and EQ them to sound better.

So whichever route you decide to go, make sure you go to an experienced installer who knows what a frequency sweep is, a scope is, and what an RTA is and make sure he knows how to use them because you really need all how to hook up amp to factory car stereo to set up a processor correctly in a vehicle like this.

Do I have to splice the LOC on both subs or just one? Portable Factory Finished Cabins — Enterprise Center Giddings Amp hook up to factory radio - Kevin, most late model vehicles do not have rca outputs on the factory radio to feed an audio signal to your aftermarket amplifier.

Featured Video

Also, the watt amp has watts rms x 1 channel 4 ohms bridgedand my sub is 4 ohms, watts rms watts max. This is called the remote wire.

how to flirt with someone out of your league

You can choose between three options: Comment by ModifiedLife on March 18th, Once connected, you'll hear clean, well-defined sound including the lyrics to your favorite song. How do i hook up the amp wires to the factory stereo Danny June 29, at 9: Sy July 8, at 9: A typical Head Unit will push between 10 and 50 watts to each speaker, while the RCA inputs on your Amplifier will only take about 3.

How to hook a car amp up to your PC | TechPowerUp Forums

Any ideas as to what could be wrong? Well if you got any old "RCA" cables what i would do is cut the end off of one and wire it to the back speakers and then you plug them in to the amp and then hook up the power supply for your amp and then connect your subs and that should work???

I want to keep the look of my truck stock so I may swap out the stock door speakers, tweeters, and center speaker. I can include pictures if needed. Using the same type of Y cable, connect the small plug to the matching jack on the rear of the iPod dock.

Choose a video to embed

You would need to use the remote turn on lead from your aftermarket radio usually blue with a white stripe and wire that to the amp turn on lead in the car harness.

I'm not sure whether the - on the speakers really needs to be connected to the - on The Amp, but do it just to be safe my speakers just have 2 nondescript wires, and they work fine. Do i have to keep the harness plugged into the head unit or do i have to keep it unplugged as i read somewhere you cannot power the speakers from both factory hu and amp simultaneously.

Those will be designed to do the tuning and tweaking themselves, making it a much simpler install. Mathew May 4, at 8: That is feeding the actual audio signal to the amp.

Wie Daten Ihre Werbeerlebnisse verbessern

Next you will need to isolate you front and rear channels both left then right for your sound and sense these are not labled you will need to check resistence of these wires which an ohm meter to tell you which wires are which you will have to have your radio on while doing this so you can fade your front and rear as well as your left and right doing it in sequence fade to your front left first hook up you ohm meter to check to see what your resistance is your ohm meter will read a negitive to the side you have faded thus it will give you your left and righ front and rear as you do this in sequence.

Connecting the iPod via headphone jack All you need is a simple Y cable, which is available from any home-electronics store.

how to hook up roku with cable box

Would you like to merge this question into it? Also, use wiring caps to connect the wires if there is no clear plug-in system.

Factory radio amp hook up

Any Mom and Pop Stereo Shop should be familiar with this item, and should have some in stock, they are very commonly used in your situation, and are not new to the industry. First you need to check your wires and sense you dont have a harness that is color coated to tell you what wires go where.

ecopolitics online dating

The amplifier amplifies that audio signal and feeds it the speaker output. So you can and are supposed to have your LOC installed along side your rear speakers.

laskovyj maj online dating

If you have a power antenna there should be a connection for that on the new stereo and the wiring schematic will tell you which one that is.