X12 turtle beach hook up. Discussions - hook up turtle beach x12 · gitbook (legacy)
Turtle beach x12
The headset's power supply may be damaged or not up to the task of handling the power demands of both the computer and the headset, even with no other USB devices connected. This allowed me to get to the pins of the connector. Conclusion — without the amp the quality of the music is still amazing — this headset has excellent fidelity for its price about 30 bucks refurbished.
Upon cracking it open I found there was plenty of room.
How do i hook up a turtle beach x12 to a sony bravia?
Disconnect some other unnecessary USB devices from the computer and then try using the headset. I drilled snug holes with a cordless drill and super glued the switches in place.
This allowed the left and right signal to bypass the amplifier completely and go right to the speakers. I once saw elizabeth mitchell dating mic-mute indicator light red and mic-on indicator light green on the tip of the mic on higher quality headsets so the user knows for sure if the mic is muted or not with his peripheral vision.
You may be suffering the effects of a ground loop, which occurs when the headset is connected to two devices that are both plugged into an AC adapter with a grounding prong. Next, I glued the corners of the amp board to the plastic ear muff housing x12 turtle beach hook up also hot glued the dials and mic mute into their proper place on the rim of the plastic ear muff.
I wanted this feature - so I ran some tiny paint coated transformer wire down the mic arm and into the tip of the plastic x12 turtle beach hook up housing — which I cut a hole in and embedded the LEDs in hot glue and then glued the blob to the plastic housing so they could be seen.
I bought the X12 turtle beach headset in hope that I could use it not only with pc or console gaming, but also as a high quality headset for talking on the road from my cell phone. The headset comes with this deplorable control box on the cable.
I cut open the Ps2 connector with a razor blade, snipped most of the glue aways and melted all the internal glue with a hot air gun so I could shovel the rest out with a pair of tweezers.
My approach was to use a hot air gun to melt all the solder on the board while it was lifted in the air with a helping hand stand. Make sure the chat volume isn't turned down in the gaming consoles audio settings or in your computer's audio settings.
Turtle beach x12
I easily mounted the female Ps2 connector into the headset in a large cutout hole with super glue and hot glue. The headset is said to require usb power for use, but I figured that I could work around that problem. I also colored both connectors black instead of that teal color.
I did this by salvaging a female Ps2 connector from an old ITX motherboard and a male Ps2 connector from an old mouse that was lying around. A buzzing or hissing sound while the headset is connected to the Xbox wireless controller can be the result of the charging cable and headset being connected to the controller at the same time.
Access the sound settings in each gaming console and then set up the console to output all audio through the headset only. If you're encountering this problem listening to audio in a program on your computer, ensure that the balance output of the program is set to play in both the left and right channels and not just one channel.
Turtle Beach Ear Force X12 - iFixit
What I wanted to do is shove all the components from within that control box in the left ear muff of the headset. My engineer colleague had supposed having the speakers and mic on the same ground would cause interference.
This control box also got in the way of my idea to make the headset cable replaceable which usually happens after about a year of hard use. You can find these cables at most electronics stores or order them from Turtle Beach. Details I needed to remove the dials and the switch from the board because I wanted to have them accessible from the rim of the ear muff.
4 Suggested Answers
However, over the past 24 hours of use and with the long phone call I made — There was no interference on my end or his WIN! I had seen headphones my size with 50 mm speakers driven only by the audio source without an amplifier in the past. If the headset is connected to a PC, this means ensuring the green connector is plugged in firmly to the headphone jack on the PC, and if you're connecting the headset to a gaming console, this means ensuring the red and white audio cables are firmly connected to the correct audio outputs on the audio source and that those cables are firmly connected to the green connector on the headset's primary cable.
After soldering the proper length wires to each leg of the component and then to the proper pad, I began to cut slots out of the edge of my plastic ear muff for the dials to be mounted later. Alternatively, if your gaming console is set correctly or you're hearing an echo in your headset during a game on one of the gaming consoles or on a PC, you may be hearing the external audio coming through the headset of someone in your party.
However, each of these components had a minimum of 5 pins. My next task was to make the headset disconnect-able from the cable.
I ran the LED ground lines to the mic ground line. Check the computer's power supply for signs of physical damage, and also check the specifications on the power supply to see if it can handle the power needs of both the PC and the headset.
Make sure the mic cable is firmly connected to the mic input jack on a computer or that the audio cables connecting the headset to the gaming console are all firmly connected.
It has 3 dials, a switch, 2 LEDs and the amplifier in it. So, I used my other switch for bypassing the amp board with the mic and switching the ground for the speakers from signal ground to common ground which the mic and amp board used. However, if I want to use the amp board for full functionality with the dials and boosted bass — I need to switch everything back by flipping the switches or there will be no sound.
Most of these problems can be resolved through troubleshooting, keeping you from having to fork over the cash for another nice headset or having to revert back to the headset that came with your gaming console.
Connect one or both of the power cables to two-prong adapters and then connect them to an AC outlet and see if you're still experiencing that specific problem. However, keep in mind that you'll need to change this setting when you don't want to use the headset.
They clearly say in the description that this headset will not work without 5v USB power but i say: I then took the headset cable which needed 5 pins for power, ground, left signal, right signal, and mic and soldered it to the bare connector and reversed the process — putting hot glue around wires and gluing the Ps2 connector sheath with super glue.
They hold very firm. If it can't, consider upgrading the PC's power supply.
However, the ground the speakers used needed the amplifier to be powered in order to work signal ground: I then pulled out the component whenever I saw all the solder was melted very carefully with tweezers. This technique worked perfectly and barely damaged the plastic components. I want one that is 4 feet long for easy on person carrying that has a 4 conductor 3.
My last feature that I needed to do was bypass the amplifier so I could use the mic and headset on a cell phone. Checking your computer's audio settings to ensure the mic isn't muted and move the "Mute" button on the control plate on the headset's primary cable until the light on the control plate is green to un-mute the mic.
I wanted all that stuff — but I found that I always bumped it or could never find it easily without looking.